With the advancement of science and technology, we can use the laser level to make our work better and easier. The laser level is an intelligent display device. The function of the laser level is that it can be installed on a moving object, collect the signal of the horizon, display the horizon in a larger field of view, and display the motion posture of the object in real-time.
How Do You Use Huepar Level?
If the laser level is applied to the aircraft, it is of great significance to prevent spatial orientation obstacles. In addition, it is also widely used in the fields of construction and decoration. Huepar laser levels can be used for indoor, outdoor, tiles laying, and so on. In the following passage, we will introduce how you use Huepar level in these aspects in detail.
How Do You Use Huepar Level for Indoor
1. If you want to hang a frame or curtain with a laser level
You must first determine the height of the top of the frame or curtain. If you plan to install curtain rods, you may want to measure about 4 inches above the window. After measuring the height, make a mark on the wall anywhere within the measurement.
Second, you need to turn on your laser level. Adjust its laser so that the beam goes horizontally across the height you marked on the wall.
Third, you need to level your laser. If it’s a manual laser level, adjust its bubble, if it’s an automatic self-leveling model, allow it to self-level. After leveling the laser level, use a suction cup or bracket to secure it to the wall.
2. If you want to Install the cabinet
You need to mount the laser level on a tripod a few inches from the wall where the cabinet will be placed before using the laser level for cabinet installation.
First, you need to use a stud finder to locate the stud. Then, mark their centers. After that, turn on the laser level and align its vertical beam so that it passes through the stud marks.
Next, you need to measure the height of the kitchen cabinets from top to bottom. Then, mark that measurement on the wall. Aim the horizontal beam of the laser level at the marked portion on the bottom of the kitchen cabinet. After that, install a ledger or support rail under that bottom line and screw it into the stud marks.
Finally, you need to align the horizontal beam of the laser so that it passes through the marked top of the kitchen cabinet. Lay your cabinets on the ledger and align their tops with the horizontal beams. Then you can screw the cabinets into the studs.
How Do You Use Huepar Level for Outdoor
It may be difficult to see the laser outside with the naked eye. At this time, you need to use green/red goggles, which will enhance the visibility of the green/red laser line outdoors. However, you still need a receiver to use the laser level outdoors. You may require dot laser levels for drywall work or cross-line laser levels to display horizontal and vertical lines across every wall in an enclosed room.
Using a Huepar level for outdoor work, you need to place the laser level on a tripod and turn it on first.
Second, you must aim the laser level at the position you want to read. Once found, lock the laser level into position.
Third, You need to bring the laser receiver to the location you want to read. Either use the magnet that comes with the laser receiver or place it on a flat surface at the same height as the laser level. Here, a second tripod is a good option.
Next, you need to move the laser receiver slowly until it catches the laser beam from the level. Once you find the beam, lock the receiver in place (if on a tripod or slope pole) or stabilize it (if on a flat surface or attached via a magnet).
Finally, you must use the spirit level and receiver to find the alignment or status of the spirit level you want.
How Do You Use Huepar Level for Tiles Laying
Tiles Laying is a seemingly simple but complex task. However, if you follow the right steps and use a Huepar laser level (eg. Huepar Green Laser Level FL360G), you can do it easily.
Before starting tile laying, you should test to determine the best layout. You can do this by laying tiles in the middle of the room. If you have some bold patterns, now is the time to try them.
To be on the safe side, you should choose rough or textured tiles, as smoother tiles tend to slip when wet. Also, it must be sure to mark the border tiles after measuring to ensure proper cutting.
For best accuracy, you must ensure that the laser square is placed on a flat surface. If you are working in a large room, you should move the laser block forward as you work.